Let’s look at Building An Easy And Cost-effective Greenhouse On Your Back Yard
Thorough planning and preparation is essential before starting your greenhouse project. Putting up a greenhouse need not be time-consuming or expensive. Your greenhouse design will very much depend on your home’s home architecture, space and plants that you want to grow, cost and available location. Make sure that your greenhouse should provide the environment suitable for your chosen type of plants.
Location
Your greenhouse must be built in a site where it will get the full and concentrated sunlight.
Your best option is the “southeast side” of your house or shade of trees. All day sunlight is best, though also consider the morning sunlight coming from the east side because this is adequate for most plants, as it permits the course food production to start early so then progress is maximized.
The location on the east captures most of the November up to February sunshine.
Deciduous trees like oak and maple can shade the greenhouse effectively from the strong late afternoon sun during the summer but they must not shade or cover your greenhouse during the morning. These trees likewise permit maximum sun exposure during the winter due to the shedding of their foliage during fall.
Your greenhouse must not be located beside trees having leaves all year as it will block the winter sun. You must maximize greenhouse exposure to winter sun especially if your greenhouse will be used year-round.
Another necessity for the location of your greenhouse is good drainage. When needed, construct your greenhouse higher than the ground so as irrigation and rainwater will easily drain away.
Light that is required by certain types of plants that you will grow, water, electricity, heat and protection from strong wind are other factors that should also be considered.
Also, you need to set up a workplace and an area for storage of your supplies in your greenhouse.
Here is a simple and easy to construct greenhouse:
Materials:
5 pieces of 20 foot each “of 5/8 inch” rebar, cut into 1/3’s – 6 foot in length.
7 pieces of 20 foot schedule” 40 PVC” drilled with a hole size 3/16 to ¼ inch “dead center” at 10 feet.
84 feet that is “cut into 4 foot lengths” of “½ schedule 40 PVC”
80 pieces size 2X4 wood (treated).
4 pieces fence posts, 8 foot in length (treated).
Size “40X24 fee” UV “polyethylene”, stabilized
60 pieces 2 ½ inches fence staples
1. Begin by extending a thin rope or string where the “two long sides” of your greenhouse should be. Then pound the 6 foot rebar in, each with a distance of 4 feet away from each other, in a “straight line” and allowing 48 inches to protrude from the soil or ground.
2. Nail the 2X6 runner on to the “rebar stakes”. This will provide you with something so as to nail on the polyethylene later. You may use a “60 2 ½ inch fence staples”.
3. Slide in the PVC pieces (20 inch) over the “rebar stakes”, making certain that no sharp points are exposed, such as rebar, wire ends, rough pipes, etc.
4. Put the PVC pieces (20 foot) on the “rebar stakes”. You need to have somebody do “one side” as you also do the “other side” carefully and slightly at each time. Make sure that you drilled holes “parallel to the ground”.
5. Slide the wire all through the PVC holes and through the 8 PVC (4foot) pieces “along the roof”.
6. So as the “ribs” will not shift horizontally, you need to wire together the 4 foot PVC pipe lengths with either baling or copper wire. Make certain that the wire is wrapped so that the PVC pipe is forced inward.
7. Construct now the “two end walls” and the doors. Use vertical posts (4X4) 10 foot length and buried 3 or 4 feet for the doorway frame. Make certain that the end walls are not floppy and must stay vertically so that the PVC will not separate. Your door must be very tight so that the wind will not be able to inflate the greenhouse.
8. Drive some nails into the post’s base horizontally of the posts and submerge them to the ground.
9. With somebody’s help, and each person on each side holding the plastic, slide it over the rib cage and then attach the ends by wrapping the plastic’s end around lath pieces then “nail the lath” to the “end walls” and also along the foundation.
10. Be creative and add a few of your personal touches.
All done! Have fun in your greenhouse!
Popular Questions
What is the most affordable way to build an easy greenhouse in your backyard?
Use a simple timber or recycled-pallet base with a lightweight PVC or wood frame. Cover the frame with greenhouse plastic rather than glass to reduce material and installation costs. Choose a level, sunny location close to a water source so the greenhouse is inexpensive to operate as well as build.
What materials are needed for building a cost-effective backyard greenhouse?
Gather treated lumber for the base, PVC pipe or narrow wooden boards for the frame, greenhouse plastic sheeting, screws, hinges, and simple door hardware. Use strong clips, battens, or staples to secure the covering and prevent wind from lifting it. Reclaimed windows or old shelving can also lower costs when they are clean, sound, and safe to use.
How do you build an easy and cost-effective greenhouse on your backyard site?
Start by clearing and leveling the area, then anchor a rectangular base firmly to the ground. Attach the frame to the base, add a door and vents, and stretch the plastic covering tightly over the structure. Seal gaps around the edges while leaving adjustable ventilation openings to control heat and humidity.
How can you keep a low-cost backyard greenhouse warm and well ventilated?
Place the greenhouse where it receives several hours of direct sunlight, preferably with protection from strong winds. Open the door or vents on warm days and close them before temperatures fall in the evening. Add water-filled containers to absorb daytime heat, and use a small fan or shade cloth when heat and humidity become excessive.
